taper加工什么意思中文翻译

㈠ 羽毛球拍taper shaft constraction什么意思翻译

taper shaft constraction
锥形轴结构
-----------------------------------
如有疑问欢迎追问！
满意请点击右上方【选为满意回答】按钮

㈡ The Economist 里的一句句子怎么翻译，"taper its quantitative easing"是什么意思

美国联邦储备理事会(美联储,fed)感到有足够的信心“锥形”其量化宽松政策(或量化宽松政策,用新发行的货币购买债券)。

㈢ 英文point是什么意思,point翻译解释,point中文意思,point用法及读音

point
[pɔint]
n.观点,看法,要点,重点,特点,点,地点,小数点,尖端,岬角,海角,意义,目标,分数,(罗盘上的)方位点,(温度的)点,插座,(字体)磅值
v.指,指向,朝向,瞄准,灰泥或水泥勾（某物）的砖缝
例句与用法：
`But she might not agree.' `You've got a point there/That's a point'.
｀可是她有可能不同意呀.＇｀你说得对[有道理].＇
At one point I thought she was going to refuse,but in the end she agreed.
当时我以为她要拒绝,但最後她却同意了.
I don't see the point of her last remark.
我不明白她最后那句话的意思.
I'm in a hurry,so come to the point.
我赶时间,直接了当说出来吧.
词形变化：
动词过去式:pointed | 动词过去分词:pointed | 动词现在分词:pointing | 动词第三人称单数:points |
名词 point:
a geometric element that has position but no extension
the precise location of something; a spatially limited location
a brief version of the essential meaning of something
a specific identifiable position in a continuum or series or especially in a process
同义词：degree,level,stage
an isolated fact that is considered separately from the whole
同义词：detail,item
an instant of time
同义词：point in time
the object of an activity
a V shape
同义词：tip,peak
a very small circular shape
同义词：dot
the unit of counting in scoring a game or contest
a promontory extending out into a large body of water
a distinct part that can be specified separately in a group of things that could be enumerated on a list
同义词：item
a style in speech or writing that arrests attention and has a penetrating or convincing quality or effect
an outstanding characteristic
同义词：spot
sharp end
any of 32 horizontal directions indicated on the card of a compass
同义词：compass point
a linear unit used to measure the size of type; approximately 1/72 inch
a punctuation mark (.) placed at the end of a declarative sentence to indicate a full stop or after abbreviations
同义词：period,full stop,stop,full point
a V-shaped mark at one end of an arrow pointer
同义词：head
the property of a shape that tapers to a sharp tip
同义词：pointedness
a distinguishing or indiviating characteristic
the gun muzzle's direction
同义词：gunpoint
a wall socket
同义词：power point
a contact in the distributor; as the rotor turns its projecting arm contacts them and current flows to the spark plugs
同义词：distributor point,breaker point
动词 point:
indicate a place,direction,person,or thing; either spatially or figuratively
同义词：indicate,show
be oriented
同义词：orient
direct into a position for use
同义词：charge,level
direct the course; determine the direction of travelling
同义词：steer,maneuver,manoeuver,manoeuvre,direct,head,guide,channelize,channelise
be a signal for or a symptom of
同义词：bespeak,betoken,indicate,signal
sail close to the wind
同义词：luff
mark (Hebrew words) with diacritics
mark with diacritics
mark (a psalm text) to indicate the points at which the music changes
be positionable in a specified manner
intend (something) to move towards a certain goal
同义词：target,aim,place,direct
give a point to
同义词：sharpen,taper
repair the joints of bricks
同义词：repoint

㈣ male-female taper怎么翻译

内外丝接头。

㈤ "shame"and"boring"翻译成中文是什么意思谢谢！

shame的中文翻译

名词 n.

1.羞耻(心),羞愧(感)[U][(+at)]
2.羞辱,耻辱[U][(+on)]
3.带来耻辱的人(或事)[S][(+to)]
4.憾事;倒霉的事专;令人憎恶的事[S]
及物动词 vt.
1.使感到属羞耻[(+for)]
2.使感羞愧而...[(+into/out of)]
3.使蒙受羞辱,使丢脸[(+by)]
4.胜过,使相形见绌

boring的中文翻译
boring1
形容词 a.

1.钻孔用的

名词 n.

1.钻孔;挖洞[U]
2.钻成的孔[C]
3.钻屑;镗花[P]

boring2
形容词 a.

令人生厌的;乏味的

㈥ 求机械专业术语的解释及英文翻译

1）电化学腐蚀 electrochemical corrosion
电化学腐蚀就是金属和电解质组成两个电极，组成腐蚀原电池。
2）车架 automotive chassis
车架是跨接在汽车前后车桥上的框架式结构，俗称大梁，是汽车的基体。
3）悬架 suspension
悬架是汽车的车架（或承载式车身）与车桥（或车轮）之间的一切传力连接装置的总称，其作用是传递作用在车轮和车架之间的力和力扭，并且缓冲由不平路面传给车架或车身的冲击力，并减少由此引起的震动，以保证汽车能平顺地行驶。
4） 转向器 redirector
转向器的作用是把来自转向盘的转向力矩和转向角进行适当的变换（主要是减速增矩），再输出给转向拉杆机构，从而使汽车转向，所以转向器本质上就是减速传动装置。
5）变速器 speed changer
变速器是用来改变来自发动机的转速和转矩的机构，它能固定或分档改变输出轴和输入轴传动比，又称变速箱。
6）板料冲压 sheet metal parts
板料冲压是利用冲模，使板料产生分离或变形的加工方法。因多数情况下板料无须加热，故称冷冲压，又简称冷冲或冲压。
7）孔加工 spot facing machining
孔加工一般分为钻孔，铰孔，扩孔，镗孔，拉孔。 机床上对孔的加工可以用钻头、镗刀、扩孔钻头、铰刀、拉刀进行钻孔、镗孔、扩孔、铰孔和拉孔。
8） 刚度 rigidity
刚度是指材料或结构在受力时抵抗弹性变形的能力。是材料或结构弹性变形难易程度的表征。
9）标准件 standard component
标准件是指结构、尺寸、画法、标记等各个方面已经完全标准化，并由专业厂生产的常用的零（部）件，如螺纹件、键、销、滚动轴承等等。
10） 脆性材料 brittleness material
在外力作用下（如拉伸、 冲击等）仅产生很小的变形即破坏断裂的材料。脆性材料在外力作用下（如拉伸、 冲击等）仅产生很小的变形即破坏断裂的性质。
11）垫圈 washer
指垫在被连接件与螺母之间的零件。一般为扁平形的金属环，用来保护被连接件的表面不受螺母擦伤，分散螺母对被连接件的压力。
12） 塑性变形 plastic distortion
塑性变形是物质-包括流体及固体在一定的条件下，在外力的作用下产生形变，当施加的外力撤除或消失后该物体不能恢复原状的一种物理现象。

㈦ ANSI B1.20.1—NPTP这个翻译成中文怎么写又是什么意思

NPT- National Pipe Taper Threads - ANSI B1.20.1

国家螺纹管标准 ANSI B1.20.1

Characteristics of NPT (also known as ANSI/ASME B1.20.1 Pipe Threads, General Purpose):

该标准规定:

tapered thread 1o 47' 锥形螺纹 1度47分
truncation of roots and crests are flat 顶部和根部的截断面是平的
60o thread angle 60度的螺纹断面角
pitch is measured in threads per inch 斜度以每英寸的螺纹分布计算

Note! Pipe sizes do not refer to any physical dimensions. The outside diameter of a pipe or fitting must be measured and compared to a table for size identification. A 3/4" NPT pipe thread has an outside diameter - OD - of 1.050 inches.

Each thread size has a defined number of threads per inch - TPI, or pitch. The 3/4" NPT pipe thread has 14 threads per inch. Both the TPI and OD of the thread are required for positive identification of thread size because more than one size have the same TPI.

NPT - American Standard Pipe Taper Thread 1)
Pipe Size
(inches) Threads per Inch
TPI - pitch Outside Diameter
OD
(inches)
1/16" 27 0.313"
1/8" 27 0.405"
1/4" 18 0.540"
3/8" 18 0.675"
1/2" 14 0.840"
3/4" 14 1.050"
1" 11-1/2 1.315"
1-1/4" 11-1/2 1.660"
1-1/2" 11-1/2 1.900"
2" 11-1/2 2.375"
2-1/2" 8 2.875"
3" 8 3.500"
3-1/2" 8 4.000"
4" 8 4.500"
5" 8 5.563"
6" 8 6.625"
8" 8 8.625"
10" 8 10.750"
12" 8 12.750"
14" 8 14.000"
16" 8 16.000"

1) The taper is 1/16 inch in an inch, which is the same as 3/4 inch in a foot (angle 1o 47')

NPT threads are not interchangeable with NPS - National Pipe Straight - threads.

NPT threads may look similar to ISO 7/1 threads. However, ISO and NPT threads should not be mixed. ISO threads have 55o taper angle versus 60o for NPT. The NPT root and crest configurations are also different from ISO. For ISO threads pitch is usually measured in millimeters (may be expressed in Inch). The pitch are different.

Sponsored Links

㈧ 锥形桥(taper type),翻译对吗

嗯，差不多对了
比较标准的是：The tapered bridge

㈨ ANSI B1.20.1—NPTP这个翻译成中文怎么写又是什么意思

NPT- National Pipe Taper Threads - ANSI B1.20.1

国家螺纹管标准 ANSI B1.20.1

Characteristics of NPT (also known as ANSI/ASME B1.20.1 Pipe Threads, General Purpose):

该标准规定:

tapered thread 1o 47' 锥形螺纹 1度47分
truncation of roots and crests are flat 顶部和根部的截断面是平的
60o thread angle 60度的螺纹断面角
pitch is measured in threads per inch 单位罗纹数以每英寸计算

Note! Pipe sizes do not refer to any physical dimensions. The outside diameter of a pipe or fitting must be measured and compared to a table for size identification. A 3/4" NPT pipe thread has an outside diameter - OD - of 1.050 inches.

备注：管的尺寸不是指物理容积。管的外部直径和属性必须以下面这个表格来确定。例如：一个标准为3/4" NPT的管外部直径为1.050英寸。

Each thread size has a defined number of threads per inch - TPI, or pitch. The 3/4" NPT pipe thread has 14 threads per inch. Both the TPI and OD of the thread are required for positive identification of thread size because more than one size have the same TPI.

每种罗纹管每英寸有固定的罗纹数（单位的罗纹数）。TPI或pitch就是单位的罗纹数。 3/4" NPT标准的罗纹管每英寸有14条罗纹。由于不同的标准中可能会出现同样的单位罗纹数。因此每个标准必须有固定的单位的罗纹数（TPI)和固定的外部直径（OD)。

NPT - American Standard Pipe Taper Thread 1)
Pipe Size 管的尺寸
(inches) Threads per Inch 单位罗纹数
TPI - pitch Outside Diameter 外部直径
OD
(inches)

管的尺寸 单位罗纹数 外部直径
1/16" 27 0.313"
1/8" 27 0.405"
1/4" 18 0.540"
3/8" 18 0.675"
1/2" 14 0.840"
3/4" 14 1.050"
1" 11-1/2 1.315"
1-1/4" 11-1/2 1.660"
1-1/2" 11-1/2 1.900"
2" 11-1/2 2.375"
2-1/2" 8 2.875"
3" 8 3.500"
3-1/2" 8 4.000"
4" 8 4.500"
5" 8 5.563"
6" 8 6.625"
8" 8 8.625"
10" 8 10.750"
12" 8 12.750"
14" 8 14.000"
16" 8 16.000"

1) The taper is 1/16 inch in an inch, which is the same as 3/4 inch in a foot (angle 1o 47')
1） 锥度为每英寸1/16英寸和每英尺3/4英寸是一样的。

NPT threads are not interchangeable with NPS - National Pipe Straight - threads.
国家螺纹管标准和美国标准直管螺纹（NPS）是无法互换的

NPT threads may look similar to ISO 7/1 threads. However, ISO and NPT threads should not be mixed. ISO threads have 55o taper angle versus 60o for NPT. The NPT root and crest configurations are also different from ISO. For ISO threads pitch is usually measured in millimeters (may be expressed in Inch). The pitch are different.

国家螺纹管标准可能会像ISO 7/1 国际标准化组织的7/1标准。但请不要将两种标准混淆。国际标准化组织的7/1标准有55度的罗纹标准，而国家螺纹管标准则是60度。国家螺纹管标准的顶部和底部和国际标准化组织的7/1标准也不相同。因为国际标准化组织的7/1标准通常是用毫米来度量的。罗纹也不同！
Sponsored Links

㈩ 高手请进,请翻译!

大哥，太多了，我本来英语不错，并且对机械方面感兴趣的，你的分太少了，你看那些人给你的翻译..连饲料，和导盲犬小Q都翻译出来了，，，你碰对人了，我刚从国外读完硕士回来，熟悉haas加工中心等~~~~但是 你给的太多了~~~~~我先翻译些，然后给你些建议好了，对了你自己给的翻译有问题，下面的数字有些我就不改了，太麻烦了
Geared Head Lathe Specifications 车床装夹描述
Capacity Swing over bed 20 (500mm) 床子能承载的刀架回转
Swing over crosslide 11.375 (290mm)刀架回转的限滑度
Swing in gap 30 (760mm) 马鞍内最大回转直径
Width in front of faceplate 10 (250mm) 马鞍内有效利用长度
Bedway width 15.5 (394mm) 床身宽度
Travel of cross slide 13.75 (350mm) 上滑板最程式
Travel of top side 6 (150mm) 小刀架行程
Headstock Spindle bore 4.125 (105mm) 主轴孔径
Spindle nose (camlock) D1-8 主轴夹具
Number of motor speeds 1 1号马达速度
Number of speed ranges 2 1号进给范围
Number of spindle speeds 16 16号主轴转速度
Spindle Speed Range (rpm) 26-1700(2) 主轴转速范围

太多了，建议楼主，安装mastercam英文版 用一下，然后查中文书这样全会了！！！我就翻译到这，下面给些我手头的资料：

各种冲模加工关连用语
barreling 滚光加工 belling 压凸加工
bending 弯曲加工 blanking 下料加工
bulging 撑压加工 burring 冲缘加工
cam die bending 凸轮弯曲加工 caulking ?合加工
coining 压印加工 compressing 压缩加工
compression bending 押弯曲加工 crowning 凸面加工
curl bending 卷边弯曲加工 curling 卷曲加工
cutting 切削加工 dinking 切断蕊骨
double shearing 叠板裁断 drawing 引伸加工
drawing with ironing 抽引光滑加工 embossing 浮花压制加工
extrusion 挤制加工 filing 锉削加工
fine blanking 精密下料加工 finish blanking 光制下料加工
finishing 精整加工 flanging 凸缘加工
folding 折边弯曲加工 folding 摺叠加工
forming 成形加工 impact extrusion 冲击挤压加工
indenting 压痕加工 ironing 引缩加工
knurling 滚花 lock seaming 固定接合
louvering 百叶窗板加工 marking 刻印加工
necking 颈缩加工 notching 冲口加工
parting 分断加工 piercing 冲孔加工
progressive bending 连续弯曲加工 progressive blanking 连续下料加工
progressive drawing 连续引伸加工 progressive forming 连续成形加工
reaming 铰孔加工 restriking 二次精冲加工
riveting ?接加工 roll bending 滚筒弯曲加工
roll finishing 滚压加工 rolling 压延加工
roughing 粗加工 scrapless machining 无废料加工
seaming 折弯重叠加工 shaving 缺口修整加工
shearing 切断加工 sizing 精压加工/矫正加工
slitting 割缝加工 spinning 卷边?接
staking ?固 stamping 锻压加工
swaging 挤锻压加工 trimming 整缘加工
upsetting 锻粗加工 wiring 抽线加工

冲压机械及周边关连用语
back shaft 支撑轴 blank determination 胚料展开
bottom slide press 下传动式压力机 board drop hammer 板落锤
brake 煞车 buckle 剥砂面
camlachie cramp 铸包 casting on flat ?合
chamotte sand 烧磨砂 charging hopper 加料漏斗
clearance 间隙 closed-die forging 合模锻造
clump 夹紧 clutch 离合器
clutch brake 离合器制动器 clutch boss 离合器轮壳
clutch lining 离合器覆盖 coil car 带卷升降运输机
coil cradle 卷材进料装置 coil reel stand 钢材卷料架
column 圆柱 connection screw 连杆调节螺钉
core compound 砂心黏结剂 counter blow hammer 对击锻锤
cradle 送料架 crank 曲柄轴
crankless 无曲柄式 cross crank 横向曲轴
cushion 缓冲 depression 外缩凹孔
dial feed 分度送料 die approach 模口角度
die assembly 合模 die cushion 模具缓冲垫
die height 冲压闭合高度 die life 模具寿命
die opening 母模逃孔 die spotting press 调整冲模用压力机
double crank press 双曲柄轴冲床 draght angle 逃料倾斜角
edging 边锻伸 embedded core 加装砂心
feed length 送料长度 feed level 送料高度
filling core 埋入砂心 filling in 填砂
film play 液面花纹 fine blanking press 精密下料冲床
forging roll 辊锻机 finishing slag 炼后熔渣
fly wheel 飞轮 fly wheel brake 飞轮制动器
foot press 脚踏冲床 formboard 进模口板
frame 床身机架 friction 摩擦
friction brake 摩擦煞车 gap shear 凹口剪床
gear 齿轮 gib 滑块引导部
gripper 夹具 gripper feed 夹持进料
gripper feeder 夹紧传送装置 hammer 槌机
hand press 手动冲床 hand rack pinion press 手动齿轮齿条式冲床
hand screw press 手动螺旋式冲床 hopper feed 料斗送料
idle stage 空站 inching 微调尺寸
isothermal forging 恒温锻造 key clutch 键槽离合器
knockout 脱模装置 knuckle mechanic 转向机构
land 模具直线刀面部 level 水平
loader 供料器 unloader 卸料机
loop controller 闭回路控制器 lower die 下模
micro inching device 微寸动装置 microinching equipment 微动装置
motor 马达 moving bolster 活动工作台
notching press 冲缺口压力机 opening 排料逃孔
overload protection device 防超载装置 pinch roll 导正滚轮
pinion 小齿轮 pitch 节距
pressfit 压入 progressive 连续送料
pusher feed 推杆式送料 pusher feeder 料片押片装置
quick die change system 快速换模系统 regrinding 再次研磨
releasing 松释动作 reversed blanking 反转下料
robot 机器人 roll forming machine 辊轧成形
roll forming machine 辊轧成形机 roll release 脱辊
roller feed 辊式送料 roller leveler 辊式矫直机
rotary bender 卷弯成形机 safety guard 安全保护装置
scrap cutter 废料切刀 scrap press 废料冲床
seamless forging 无缝锻造 separate 分离
shave 崩砂 shear angle 剪角
sheet loader 薄板装料机 shot 单行程工作
shrinkage fit 收缩配合 shut height 闭合高度
sieve mesh 筛孔 sintering of sand 铸砂烧贴
slide balancer 滑动平衡器 slug hole 逃料孔
spin forming machine 旋压成形机 spotting 合模
stack feeder 堆叠拨送料机 stickness 黏模性
straight side frame 冲床侧板 stretcher leveler 拉伸矫直机
strip feeder 料材送料装置 stripping pressure 弹出压力
stroke 冲程 take out device 取料装置
toggle press 肘杆式压力机 transfer 传送
transfer feed 连续自动送料装置 turrent punch press 转塔冲床
two speed clutch 双速离合器 uncoiler 闭卷送料机
unloader 卸载机 vibration feeder 振动送料机
wiring press 嵌线卷边机